ROCK PROOF -H

Description

 

ROCK PROOF-H is a high-performance, elastomeric modified bitumen membrane reinforced with nonwoven polyester and fiberglass Filaments. It features a sand surface finish, designed for pre-applied and blind side waterproofing. Using SBS polymer technology, it ensures flexibility, durability, and protection against water infiltration, accommodating structural movements without cracking, even in extreme conditions. 

 

 Key Features

•Excellent adhesion to fresh poured Concrete
•Sanded Surface Finish
•Resistant to hydrostatic Pressure
•Resistant to Sea Salty water
•Chemical resistance to wide range of light
acidic, alkaline solutions and bacteria.

Transportation & Storage

– Rolls must be in an upright position on a pallet in a One-row height.
– Avoid falls or other mechanical impacts during loading and unloading of rolls
– Storage of rolls in a horizontal position is prohibited.
– Protect the rolls from direct UV-rays, any source of heat and moisture 

 

 Application

ROCK PROOF-H Pre-applied waterproofing membranes are used for a variety of applications:
–blind side installation
– Retaining walls
– As a system or base layer for multi-layer systems
–Underground waterproofing
– The product can be applied for waterproofing foundations and engineering structures by torching, hot air, or adhesives in both cold and hot applications.
– Cleaning the substrate surface is essential until it becomes dry and smooth, removing any particles.
– Based on surface conditions, a coat of ROCKAL primer may be required before applying the membrane.
– According to the waterproofing system design, SBS products can be fully bonded, semibonded, or loose laid.
– Overlapping is essential: side laps should be 8-10 cm, and end laps 12-15 cm.
– For complete instructions, refer to the ROCKAL applicator guide. 

 

Technical data

 

Test	Test Method	Tolerance	Result	Unit
Thickness	EN 1849-1	±5%	3.5	mm
Width	EN 1848-1	±1%	1	m
Length	EN 1848-1	±1%	10	m
Straightness	EN 1848-1	-	± 6	mm
Softening Point (R&B)	ASTM D-36	≥	120	0C
low temperature	EN 1109 ASTM D-5147	-	- 13 : - 15	0C
Flow resistance at elevated temperature	EN 1110 ASTM D-5147	-10	110	0C
Tensile Strength-Longitudinal	EN 12311-1ASTM D-5147	± 20%	800	N/5cm
Tensile Strength-Transverse	EN 12311-1ASTM D-5147	± 20%	500	N/5cm
Elongation @Break -Longitudinal	EN 12311-1ASTM D-5147	± 15	40	%
Elongation @Break -Transverse	EN 12311-1ASTM D-5147	± 15	45	%
Tearing Strength-Longitudinal	EN 12310-1	≥	220	N
Tearing Strength-Transverse	EN 12310-1	≥	240	N
Tensile Tear Resistance-Longitudinal	ASTM D-5147 D-4073	± 20%	500	N
Tensile Tear Resistance-Transverse	ASTM D-5147 D-4073	± 20%	400	N
Resistance to Static Loading	EN 12730	≥	15	Kg
Resistance to Impact Loading	EN 12691	≥	1000	mm
Shear Resistance of joint L/T	EN 12317-1	± 20%	750/450	N/5cm
Dimensional Stability L/T	EN 1107-1	-	1	%
Adhesion to concrete	Pelage UEATC	-	40	N/5cm
Water absorption Peel Adhesion to Concrete Reaction to fire Water Impermeability at Low Pressure Water Impermeability at High Pressure	ASTM D-5147 ASTM D903 EN 13501-1 EN 1928 method A EN 1928 method B	≤ ≥ - - ≥	0.15 3400 E Pass Pass	% N/m - 60Kpa 200Kpa
Thermal Ageing in air (in oven 4 weeks at 70 ± 2°C)	EN 1296	-	Pass	-
Ageing Due to Atmospheric Agents (U.V. Test weathering)	ASTM G 53 UNI 8202/29	-	Pass	-